MOISTURE BARRIERS / WATERPROOFING
WAKOL PU280.jpg

WAKOL PU280 - Moisture Barrier - 1 Component Ready to use Full Membrane 

Porous & NON-Porous Surfaces

***LAY FLOORS WITHIN 1-2hrs**** SAME DAY NO DELAYS!!!!!

Wakol PU 280 is a ready-to-use 1-component polyurethane primer for priming absorbent and non-absorbent subfloors, and to reinforce abraded resp. sanded concrete edges. Also for capillary ascending humidity and higher residual humidity up to 6 CM% / 98 corresponding RH % in cement screeds without floor heating, on heated cement screeds up to max. 3 CM% / 85 corresponding RH % as well as on concrete up to max. 7,5% by weight / 98 corresponding RH %; applicable as moisture barrier on unheated cement screeds and concretes without prior moisture measurement.

  • Application method: WAKOL Primer Roller, short haired velour or foam roller

  • Consumption: approx.100-150 g/m² as primer, approx. 250-350 g/m² as moisture barrier

  • Drying time: approx. 40-50 minutes

  • Storage: not below +5 °C, store in a cool place

  • Base: polyurethane resin

  • EMICODE: EC1 PLUS

Suitable Applications:

  • Concrete

  • Screed

  • Timber

  • Plywood

  • Tiles

  • Most Surfaces

Sizes Available:

  • 5L Drum

  • 11L Drum

Coverage:

1 Coat @ 150μm wet film

5L Consumption = 30 m2

11L Consumption = 70-80 m2

bostik-dampfix-platinum-400x300 - Copy.jpg

DAMPFIX PLATINUM Waterproof Membrane UNIVERSAL All-in-one 15L Pail
***One Product for all applications*** Fast Drying

Product overview
Dampfix® Platinum is an all-in-one, one-component rapid drying water based polyurethane, Class 3 waterproofing membrane system that meets the requirements of AS3740 by complying with AS/NZ 4858.

ABOUT DAMPFIX® PLATINUM

  • All-in-one waterproofing membrane

  • Class 3, high elasticity

  • Fast drying - recoat in 1-2 hours @ 22°C & 50% RH. Flood test after 24 hours @ 22°C / 50% RH

  • Can be tiled after 4-6 hours @ 22°C / 50% RH in non-critical areas

  • Compatible for tiling with Bostik tile adhesive systems

  • Excellent adhesion to concrete, rendered masonry, wet area plasterboard, FC sheet & plywood

  • Can be applied to damp substrates (provided no free surface water)

  • Brush or roller applied

  • Designed for commercial and residential application

RECOMMENDED USES
  • As a waterproofing membrane under tile to internal wet area shower, bathroom, kitchen, laundry & toilet areas when installed to AS/NZ 3740

  • As a waterproofing membrane under tile or other wearing surface systems to external balconies, rooftops & podium levels when installed to AS/NZ 4654.2

  • As an exposed waterproofing membrane to external applications subjected to light pedestrian traffic only

  • Suitable for concrete; cement rendered masonry; FC sheeting; water resistant plasterboard; and structural plywood (Type A Stamped “PAA JAS-ANZ” to AS/NZS 2269-2004) substrates

  • As a waterproofing membrane for planter boxes, retaining walls

  • As a waterproofing membrane for swimming pools, covered by tiles

Bostik_Logo_Header.png
MoistureSeal_10Lkit.png

BOSTIK MOISTURE SEAL KIT 10L -
2 Part Epoxy Set (Part A & B)

Bostik Moisture Seal is a two part, water-based, epoxy moisture and vapour barrier for priming under flooring adhesives and waterproofing membranes. Its moisture and vapour barrier formulation prevents water seepage and permeation in building and construction substrates.

 

  • 2-part kit, pre-packed and ready to mix with an easy 1:1 mixing ratio

  • Approved for direct contact with drinking water

  • Conforms to ASTM E96 water vapour transmission (negative pressure) tests

  • Withstands hydrostatic water pressure up to 25m or 259kPa

  • Suitable for use as a concrete bonding primer to consolidate concrete screeds or floors

  • Compatible with a wide range of coverings including the Bostik Ultraset flooring adhesives and Dampfix waterproofing ranges.

Recommended Uses

Moisture Seal is best suited to concrete, rendered brick, fibre cement, metal, stone, masonry and structural plywood (Type A Stamped “PAA JAS-ANZ” to AS/NZS 2269-2004) substrates. Ideal applications include walls and floors, water storage tanks and reservoirs or swimming pools. Moisture Seal is a perfect concrete primer sealer before waterproofing or tile adhesive is applied.

Coverage:

1 Coat @ 200μm wet film
1L Consumption =  4 – 5 m2

10L Consumption = 40 – 50 m2
2 Coat @ 200μm wet film
1L Consumption = 2 – 2.5 m2

10L Consumption = 20 - 25 m2

bostik-australia-ultraseal-4L-box-kit.pn

BOSTIK ULTRASEAL 4L - VAPOUR BARRIER KIT

Bostik Ultraseal is a two part, solvent free, epoxy composition compatible with a wide range of coverings. Designed as a one coat primer and vapour barrier/retarder to prevent moisture migration through a concrete slab to levels that will not cause swelling or cupping of timber flooring.

Recommended Uses

  • Interior surfaces

  • Residential applications

  • Commercial applications

Substrates

  • Floors

  • Compatible with the entire Bostik Ultraset® hardwood flooring adhesive range

Materials

  • Concrete

  • Fibre cement

  • Stone

  • Masonry

  • Structural plywood,

  • Brick

  • AAC

Coverage:

COVERAGE Coating thickness 300 μm

1L = 3 – 4 m2

4L = 12 – 16 m2